Filter By:
- Show More Brands
- Show Fewer Brands
Parts & Accessories

$15.00 - $20.00
Stan's 3.30/3.30Ti Hub Kit converts Stan's 3.30 front hubs from quick-release to through-axle compatible. Installation is easy—just pull the old ones off and put the new ones on. Conversion kits available in 12mm and 15mm.

$15.00
This replacement axle for Stan's 3.30 or 3.30Ti rear hubs gets you back on the bike where you belong. CHoose the corrct size for your frame interface.

$60.00
Replacement single-speed freehub body for Stan's NoTubes 3.30SS rear hubs. This freehub body uses stainless steel bearings.

$80.00 - $85.00
Durasync freehub bodies feature triple freehub bearings for increased axle stability to handle even greater vertical and torsional loads. This CNC machined durasync freehub is a direct replacement for your Neo hub, and includes pawls, springs, pawl retaining ring, and red freehub spacer. Bearings are pre-installed.
- 6-pawl system provides 36 points of contact and 10-degree engagement for quick acceleration
- Chromed steel bearings
- Wide bearing stance and axle design reduces flex and adds durability
- Low drag main seal prevents contamination and reduces resistance
- Mini Driver has a Shimano HG spline, but is 10mm shorter to accept 11-speed cassettes with 10t cogs from Hope and OneUp Components

$20.00 - $22.00
Front end cap conversion kits for NoTubes Neo and Neo Ultimate
- SealLock end caps feature a low friction U-cup seal that snaps into place

$9.00
Replacement springs and pawls. Includes 6 pawls, 6 springs and 1 plastic retaining ring that holds the pawls in place even during disassembly to ensure you're never searching the floor for tiny springs.

$20.00 - $23.00
Rear end cap conversion kits for NoTubes Neo and Neo Ultimate hubs
- SealLock end caps feature a low friction U-cup seal that snaps into place

$21.00
Replacement rear axle for Neo and Neo Ultimate hubs. High-precision center-less ground treatment ensures perfect bearing fit.

$11.25 - $25.00
Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims.
21mm width fits:
- ZTR Olympic
- ZTR Iron Cross
- ZTR 355
- ZTR Alpine
- ZTR Crest
- ZTR Alpha 340 (2 layers)
- ZTR Alpha 400 (2 layers)
- Most road clincher rims
25mm width fits:
- ZTR 355 (26", 650b, 29")
- ZTR Crest
- Crest MK3
- ZTR Arch EX
- ZTR Flow EX
- Crest S1
27mm width fits:
- ZTR Flow EX
- ZTR Bravo
- ZTR Hugo 52mm
- Arch S1
- ZTR Rapid 28
- ZTR Rapid 30
- Arch MK3
30mm width fits:
- ZTR Flow MK3

$16.00
Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant.
Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads:
- MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi
- ERD 615, 622x49.9, 29 in x 52.3mm
Your rim has a stepped valve and is not compatible with this Schrader valve.

$80.00
This conversion kit allows you to use SRAM's 11-speed mountain cassette on your Stan's NoTubes wheels. Each kit includes an XD freehub, spacer, drive side end cap, and three sealed bearings.

$23.00
Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.

$12.50 - $29.00
Replacement bearings for Stan's NoTubes Neo hubs. Includes 2 bearings.
- 26mm OD x 15mm ID
- 7mm thick
Page 1 of 1